Page 1 of 2

singer, ultralock 400 threading problems.

New postPosted: Sat Oct 15, 2011 1:30 pm
by dirtydaz666
i have a singer ultralock 400, 5 thread, how the heck am i ment to thread it?
i followed the pic on the flap and its not too clear and it dosnt work when i have done it.
3 days tryng and going insane!! :brick:
can anyone save me from insanity plaese?
Daz

Re: singer, ultralock 400 threading problems.

New postPosted: Sat Oct 15, 2011 5:58 pm
by MartySews2
Daz, does your manual give you instructions on threading the machine? Are you using serger thread which is different than sewing machine thread? Typically, you thread the upper looper, lower looper, right needle, left needle on a serger. Your manual will tell you your threading order. When using the 5th thread, you thread the chain looper before threading the needles. Hope this helps. Your manual should give you the info that you need.
Marty ;)

Re: singer, ultralock 400 threading problems.

New postPosted: Sun Oct 16, 2011 3:07 am
by dirtydaz666
That would be the main problem, i dont have a manual for the machine.
ive been looking for a pdf to download but to no avail. getting slightly bored now as 3 days is far too long to be thredind a machine.
i follow the picture on the flap but it dosen't explain the end of the route well and everything i try ends up with me smoking another cigarette.
do you know where to find the pdf that i need? please and thanks...
DaZ

Re: singer, ultralock 400 threading problems.

New postPosted: Sun Oct 16, 2011 4:11 am
by Mom of Six
Try Here. They will help you find your model #
http://www.singerco.com/accessories/ins ... no=14SH654

Re: singer, ultralock 400 threading problems.

New postPosted: Sun Oct 16, 2011 4:47 am
by dirtydaz666
they don't have it, story of my life at the moment! :brick:
or maybe they do, need to go to the workshop and find out if i wrote the number down correctly,
also i just noticed that its to buy a manual, i dont want to buy 1 due to the fact i have no money at the moment,
anyone know where i can get a free 1?
and thanks.
DaZ

Re: singer, ultralock 400 threading problems.

New postPosted: Sun Oct 16, 2011 8:47 am
by sewingmom
DaZ, Is that the complete name of the machine. I have been searching but can't find a free threading diagram either. Try going to Singer.com and e-mailing customer service and see if they will direct you to a site for a free manual and/or threading diagram. You most probably want a manual because there are a lot of tricks to adjusting tensions etc that are specific to each serger/sewing machine. I wish you success. Your local Singer dealer might be willing to tell you where to look for a manual. Just tell them your financial situation. Many people will be glad to help a fellow Singer owner out. Hey! Look for a forum that discusses the singer ultralock 400 but be sure you have al your information as to the name and serial number, before you waste your time searching.

Re: singer, ultralock 400 threading problems.

New postPosted: Sun Oct 16, 2011 4:36 pm
by sewingmom
http://www.singerco.com/accessories/instruction-manuals

DaZ, this is a site with manuals for purchase.

Re: singer, ultralock 400 threading problems.

New postPosted: Sun Oct 16, 2011 5:32 pm
by LeapFrog Libby
Daz, I have a serger I have had for 21 years, but I still have to look in the manual quite frequently. I cannot begin to estimate how many thousands hours I have logged on my serger, but I cannot imaging threading it without the photos to guide me, and mine are color coded for each different set. mine is a 4 thread, and the colors are green blue pink and yellow.

Re: singer, ultralock 400 threading problems.

New postPosted: Sun Oct 16, 2011 6:22 pm
by dirtydaz666
good evening, or morning as the case might be,
okies, the machine says on the front flap...singer ultraglide 400 electronic.
its got the colour code bits ie: blue, green, orange, yellow and purple.
its got the diagram with dots of colour to follow but in the end it not clear on how the threads end.
i have left it alone for today as our argument has been a long and furious 3 days.
i hope we can come to an understanding soon and create our long lasting relationship.
oh and where do i put pics of my work up? i have a few pics id like to show off.
thanks so far for the advise, keep it coming! :D
DaZ

Re: singer, ultralock 400 threading problems.

New postPosted: Sun Oct 16, 2011 7:47 pm
by MartySews2
Daz, if you can get the book "The ABC's of Sergers", it has some basic threading information with diagrams so that you can learn the parts of the machine as well as where the threads go. I think this book will help you a lot. You can find it on Amazon.
Marty ;)